Login   |  
Notice: Undefined index: basket in /opt/lampp/htdocs/english/menutop.php on line 14
(0)   |  

TEL. & FAX +66(0)2-020-3301

NPort 5600-DTL Series

Home  >   MOXA  >   Industrial Edge Connectivity  >  
Serial Device Servers  >   General Device Servers

8-port entry-level RS-232/422/485 serial device servers

Product Feature

  • 8 serial ports supporting RS-232/422/485
  • Compact desktop design
  • 10/100M auto-sensing Ethernet
  • Configure by Telnet, web browser, or Windows utility
  • Supports Real COM and TCP server, TCP client, UDP socket modes
  • SNMP MIB-II for network management

Introduction

NPort® 5600-8-DTL device servers can conveniently and transparently connect 8 serial devices to an Ethernet network, allowing you to network your existing serial devices with basic configurations. You can both centralize management of your serial devices and distribute management hosts over the network. The NPort® 5600-8-DTL device servers have a smaller form factor than our 19-inch models, making them a great choice for applications that need additional serial ports when mounting rails are not available.

 

Convenient Design for RS-485 Applications

The NPort® 5650-8-DTL device servers support selectable 1 kilo-ohm and 150 kilo-ohms pull high/low resistors and a 120-ohm terminator. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals. When using termination resistors, it is also important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible with all environments, NPort® 5600-8-DTL device servers use DIP switches to allow users to adjust termination and pull high/low resistor values manually for each serial port.

 

LED Indicators to Ease Your Maintenance Tasks

The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The NPort® 5600’s LEDs not only indicate current system and network status, but they also help field engineers monitor the status of attached serial devices.

Ethernet Interface

10/100BaseT(X) Ports (RJ45 connector)1
Magnetic Isolation Protection1.5 kV (built-in)

Ethernet Software Features

Configuration OptionsSerial Console, Telnet Console, Web Console (HTTP/HTTPS), Windows 
Utility
ManagementARP, BOOTP, DHCP Client, DNS, HTTP, HTTPS, ICMP, IPv4, LLDP, 
Rtelnet, SMTP, SNMPv1/v2c, Telnet, TCP/IP, UDP
FilterIGMP v1/v2
Windows Real COM DriversWindows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10
(x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 
5.0/6.0, Windows XP Embedded
Linux Real TTY DriversKernel versions: 2.4.x, 2.6.x, 3.x, 4.x, and 5.x
Fixed TTY DriversSCO UNIX, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6.x, Solaris 10,
FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X
Android APIAndroid 3.1.x and later
MIBRFC1213, RFC1317
Time ManagementSNTP

Serial Interface

ConnectorDB9 male

No. of Ports

8
Serial StandardsNPort 5610-8-DTL Series: RS-232
NPort 5650-8-DTL Series: RS-232, RS-422, RS-485
BaudrateSupports standard baudrates (unit=bps): 50, 75, 110, 134, 150, 300, 600, 
1200, 1800, 2400, 4800, 7200, 9600, 19200, 38400, 57600, 115200, 230.4k, 
460.8k, 921.6k
Data Bits5, 6, 7, 8
Stop Bits1, 1.5, 2
ParityNone, Even, Odd, Space, Mark
Flow ControlRTS/CTS, DTR/DSR, XON/XOFF
IsolationNPort 5650I-8-DTL Series: 2 kV
Pull High/Low Resistor for RS-4851 kilo-ohm, 150 kilo-ohms
RS-485 Data Direction ControlADDC® (automatic data direction control)
Terminator for RS-485NPort 5650 Series: 120 ohms

Serial Signals

RS-232TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422Tx+, Tx-, Rx+, Rx-, GND
RS-485-4wTx+, Tx-, Rx+, Rx-, GND
RS-485-2wData+, Data-, GND

Power Parameters

Input CurrentNPort 5610-8-DTL Series: 340 mA @ 12 VDC
NPort 5650-8-DTL Series: 470 mA @ 12 VDC
NPort 5650I-8-DTL Series: 740 mA @ 12 VDC
No. of Power Inputs1
Input Voltage12 to 48 VDC
Reverse Polarity ProtectionSupported
Source of Input PowerPower input jack

Physical Characteristics

HousingMetal
Dimensions (with ears)229 x 135.43 x 46 mm (9.02 x 5.33 x 1.81 in)
Dimensions (without ears)197 x 135.43 x 44 mm (7.76 x 5.33 x 1.73 in)
WeightNPort 5610-8-DTL Series: 1760 g (3.88 lb)
NPort 5650-8-DTL Series: 1770 g (3.90 lb)
NPort 5650I-8-DTL Series: 1850 g (4.08 lb)
InstallationDesktop, DIN-rail mounting (with optional kit), Wall mounting (with optional
kit)

Environmental Limits

Operating TemperatureStandard Models: 0 to 60°C (-32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature (package
included)
-40 to 75°C (-40 to 167°F)
Ambient Relative Humidity5 to 95% (non-condensing)

Standards and Certifications

EMCEN 55032/24
EMICISPR 32, FCC Part 15B Class A
EMSIEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
IEC 61000-4-11 DIPs
SafetyUL 60950-1

Declaration

Green ProductRoHS, CRoHS, WEEE

MTBF

TimeNPort 5610-8-DTL Series: 953,388 hrs
NPort 5650-8-DTL Series: 740,457 hrs
NPort 5650I-8-DTL Series: 258,150 hrs
StandardsTelcordia (Bellcore) Standard TR/SR

Warranty

Warranty Period5 years
DetailsSee www.moxa.com/warranty
Name Type Version Release Date
Datasheet for NPort 5600-DTL Series Datasheet V1.2 08 November 2019

Notice: Undefined variable: rs5 in /opt/lampp/htdocs/english/productview.php on line 609

Notice: Trying to get property 'tab_ap' of non-object in /opt/lampp/htdocs/english/productview.php on line 609


Notice: Undefined variable: title_ap in /opt/lampp/htdocs/english/productview.php on line 614


Notice: Undefined variable: detail_ap in /opt/lampp/htdocs/english/productview.php on line 615

PT AUTOMATION (THAILAND) CO.,LTD.

Monday - Friday : office hours 9.00 AM – 6.00 PM

EN
TH